Tools
Parts
- 2 1000mm MakerBot Endstop Cable
- 1 1m Heavy duty zip-tie
- 2 2020 Angle Corner Connector
- 1 2040 V-Slot Profile 400mm
- 2 50 mm compression spring
- 1 50mm Dowel OD6 pin
- 1 6x1 Nitrile O-ring
- 2 8x136mm Steel Rod
- 4 D6xL2 cylindrical magnet
- 2 LM8UU Linear Bearing
- 2 M4 Drop-In Nut 2020
- 1 MakerBot Endstop
- 1 NEMA 17 Cable 1000mm
- 1 NEMA 17 Short Body Stepper Motor
- 2 SPRING-L16-CS1.3-OD12
- 1 THSL Anti-Backlash Nut ID8
- 1 THSL Leadscrew OD8 L80mm
Tools
- 1 3D Printer
- 1 6 mm drill bit
- 1 CNC Lathe
- 1 Drill
- 1 M5 Tap
- 1 Silicone Grease
3D-printed part
- 2 ENDSTOP-BASE-MAKERBOT001
- 1 GIL-MOT-BAS.V2.1
- 4 M3-SEP-L10-3
- 1 PIP-BASE-LOWER
- 1 PIP-CPL-SHEATH
- 1 PIP-SUP-CR
- 1 PIP-SUP-LW.V2
- 1 PIP-SUP-STEM
- 1 PIP-TIP-EJECTOR.V1B
- 1 SPRING-WASHER
- 1 THSL-WEDGE-PLATE-COMP
- 1 TOOLPLATE-WEDGE-PIP2
- 1 TP-GIL-BASE.V2
- 1 TP-JUB-WING-BASE.V3
- 1 TP-JUB-WING-BASE.V3-MIRROR
Machined part on a CNC-lathe
Fasteners (e.g. screws, nuts, washers)
- 2 M3 Hex Nut
- 2 M3 x 10mm Screw
- 2 M3 x 12mm Screw
- 2 M3 x 20mm Screw
- 4 M4 Washer
- 4 M4 x 10mm Screw
- 2 M4 x 10mm Set screw
- 1 M4 x 16mm Conical Head Screw
- 3 M5 x 8 mm Button Head Screw
- 3 M6 x 8mm Set screw
Stock material for part fabrication
Tools:
Materials:
Parts:
- 3D-printed parts: source (default unless noted)
- Separators for motor: M3-SEP-L10-3
- Motor base: GIL-MOT-BAS.V2.1
- Pipette: PIP-BASE-LOWER
- PIP-CPL-SHEATH
- PIP-SUP-LW.V2
- Spring shim: SPRING-WASHER
- PIP-TIP-EJECTOR.V1B: source
- ENDSTOP-BASE-MAKERBOT001
- Carriage PIP-SUP-CR
- Shaft holder PIP-SUP-STEM
- Tool-changer interface:
- Parking:
- Parking wing base: TP-GIL-BASE.V2
- Parking wing TP-JUB-WING-BASE.V3
- Parking wing (mirrored) TP-JUB-WING-BASE.V3-MIRROR: source
- Tool-changer interface:
- Parts:
- Pipette:
- Plunger:
- M4 x 10mm Set screw
- Dowel pin shaft:
- Machined shaft:
- tip-holder:
- Plunger:
- Ejector post:
- Cable management: